| 263 | 11 | 4 |
| 下载次数 | 被引频次 | 阅读次数 |
研究了不同激光功率与扫描速度对SLM成形的单道CuSn10薄壁侧表面的表面形貌与粗糙度的影响，得出最优成形工艺；以上述工艺成形双道CuSn10薄壁件并研究了不同扫描间距对两成形侧表面粗糙度的影响；以上述扫描间距作为轮廓偏移量制备长直线扫描填充与短直线扫描填充的0.5 mm薄壁件。研究结果表明：在激光功率为195 W,扫描速度为550 mm/s时，成形单道薄壁件平均粗糙度最低为2.3μm±0.2μm;随着扫描间距的增大，第二成形面粗糙度减小，在扫描间距为120μm、140μm、160μm时，两平行熔道相互作用较低，对粗糙度影响较小；短直线扫描填充策略比长直线扫描填充策略成形的薄壁件侧表面粗糙度更小。当偏移量为160μm时，短直线扫描填充成形薄壁件侧表面平均粗糙度最小，达到2.27μm±0.4μm。
Abstract：The effects of different laser power and scanning speed on the surface morphology and roughness of single track CuSn10 thin-walled side surface fabricated by SLM were studied in this paper. Moreover, the optimized manufacturing process was obtained. Double track CuSn10 thin-walled parts were fabricated by the above process, and the effects of different scanning space on the surface roughness of the two forming sides were studied. Taking the above scanning space as the contour offset, 0.5 mm thin-walled parts were fabricated with two scanning strategies of long linear scanning filling and short linear scanning filling. Results show that when the laser power is 195 W and the scanning speed is 550 mm/s, the minimum average roughness of single track thin-walled parts is 2.3 μm±0.2 μm. With the increase of scanning space, the roughness of the second forming surface decreases. When the scanning space is 120 μm, 140 μm, 160 μm, the interaction between the two parallel melting is low, and the effect on the roughness is small. The short linear scanning filling has a lower surface roughness value than the long linear scanning filling. When the offset is 160 μm, the minimum average roughness value of the side surface of the thin-walled part manufactured by short linear scanning filling is 2.27 μm±0.4 μm.
[1] YANG Y Q,CHEN J,SONG C H,et al.Current status and progress on technology of selective laser melting of metal parts[J].Laser & Optoelectronics Progress,2018,55(1):011401.杨永强，陈杰，宋长辉，等.金属零件激光选区熔化技术的现状及进展[J].激光与光电子学进展，2018,55(1):011401.
[2] CHEN S,LIU J G,WANG W D,et al.Research progress in thin-walled parts formed by selective laser melting[J].Journal of Netshape Forming Engineering,2020,12(5):122-131.陈帅，刘建光，王卫东，等.激光选区熔化成形薄壁件研究进展[J].精密成形工程，2020,12(5):122-131.
[3] MAO Z F.Forming processing and properties of copper-tin alloy in selective laser melting [D].Chongqing:Chongqing University,2018.毛忠发.铜锡合金的选择性激光熔化成形工艺及性能研究[D].重庆：重庆大学，2018.
[4] REN N F,LIN K,ZHANG Z Y,et al.Research on light absorption enhancement of copper by nanosecond laser[J].Chinese Journal of Lasers,2016,43(3):0303004.任乃飞，林康，张志研，等.利用纳秒激光提高铜表面吸光率的研究[J].中国激光，2016,43(3):0303004.
[5] SCUDINO S,UNTERD?RFER C,PRASHANTH K G,et al.Additive manufacturing of Cu-10Sn bronze[J].Materials Letters,2015,156:202-204.
[6] GüNTHER J,LEUDERS S,KOPPA P,et al.On the effect of internal channels and surface roughness on the high-cycle fatigue performance of Ti-6Al-4V processed by SLM[J].Materials & Design,2018,143:1-11.
[7] UZAN N E,RAMATI S,SHNECK R,et al.On the effect of shot-peening on fatigue resistance of AlSi10Mg specimens fabricated by additive manufacturing using selective laser melting (AM-SLM)[J].Additive Manufacturing,2018,21:458-464.
[8] LI Z Y,ZHANG X G,WEN H,et al.Study on upper surface roughness of pure copper formed parts by selective laser melting[J].Applied Laser,2018,38(2):170-176.李宗义，张晓刚，文宏，等.激光选区熔化纯铜成形件上表面粗糙度的研究[J].应用激光，2018,38(2):170-176.
[9] HUANG W D,ZHANG W J,LIAN G F,et al.Effect of SLM forming process parameters on surface roughness of 316L stainless steel parts[J].Applied Laser,2020,40(1):35-41.黄卫东，张伟杰，练国富，等.SLM成形工艺参数对316L不锈钢成形件表面粗糙度的影响[J].应用激光，2020,40(1):35-41.
[10] LI Z H,KUAI Z Z,LIU B,et al.Research on surface roughness of multi-laser SLM formed parts[J].Journal of Ordnance Equipment Engineering,2019,40(9):165-168.李忠华，蒯泽宙，刘斌，等.多激光SLM成形件表面粗糙度研究[J].兵器装备工程学报，2019,40(9):165-168.
[11] TIAN Y,TOMUS D,ROMETSCH P,et al.Influences of processing parameters on surface roughness of Hastelloy X produced by selective laser melting[J].Additive Manufacturing,2017,13:103-112.
[12] WANG L Z,WANG S,WU J J.Experimental investigation on densification behavior and surface roughness of AlSi10Mg powders produced by selective laser melting[J].Optics & Laser Technology,2017,96:88-96.
[13] YANG T,LIU T T,LIAO W H,et al.The influence of process parameters on vertical surface roughness of the AlSi10Mg parts fabricated by selective laser melting[J].Journal of Materials Processing Technology,2019,266:26-36.
[14] YAN A R,YANG T T,WANG Y L,et al.Forming process and high-temperature mechanical properties of variable energy laser selective melting manufacturing IN718 superalloy[J].Optics and Precision Engineering,2015,23(6):1695-1704.闫岸如，杨恬恬，王燕灵，等.变能量激光选区熔化IN718镍基超合金的成形工艺及高温机械性能[J].光学精密工程，2015,23(6):1695-1704.
[15] SONG C H,YANG Y Q,LIU Y,et al.Study on manufacturing of W-Cu alloy thin wall parts by selective laser melting[J].The International Journal of Advanced Manufacturing Technology,2015,78(5/6/7/8):885-893.
[16] LIANG P H,TANG Q,FENG Q X,et al.Numerical simulation and experiment of single track scanning and lapping in selective laser melting[J].Journal of Mechanical Engineering,2020,56(22):56-67.梁平华，唐倩，冯琪翔，等.激光选区熔化单道扫描与搭接数值模拟及试验[J].机械工程学报，2020,56(22):56-67.
基本信息:
DOI：10.14128/j.cnki.al.20224207.052
中图分类号:TG665;TG146.11
引用信息:
[1]李忠华,李霍东,蒯泽宙,等.选区激光熔化制备CuSn10薄壁件侧表面粗糙度研究[J].应用激光,2022,42(07):52-58.DOI:10.14128/j.cnki.al.20224207.052.
基金信息:
国家自然科学基金(52075502,51905497)
2021-09-07
2021
2021-09-26
2021
1
2022-07-25
2022-07-25